Відео

Thanks for the tip. I used a 1mm drill bit in a pin vise (couple of twists with your fingers and your through the plastic with no damage). I used a light synthetic gear oil designed for model trains/cars. It safe for plastic and has a syringe style applicator so no need to drill a big hole.

What kind of battery? Rechargeable?

I destroyed it 😅

The top knob on my toaster oven just like this one got snapped off while turning. How do I remove the remaining piece(stir on the toaster oven) to repair

Thanks, we’ll give this a try! Great tutorial

Wish you had shown how to get it open.

Unltrasonic welded body. Batteries spot welded

Well, now it’s not waterproof anymore

What is the white Ribbon for?

Your video was very helpful, but I found my own method to hold the side end of the spring in place. I rolled up a very small ball of kleenex and jammed it into the larger part of the side spring hole, keeping the tab at the smaller end so it wouldn't roll back to .where it was always drifting into. Then with a micro screwdriver I pried the other end of the spring outward while sliding it into place. Voila! Couldn't have done it without your explanation. Thank you!

Thank you for that video! I have watched so many until I found in yours what I have been looking for. Totally appreciated :)

another made in WU HAN , HIGH COST & CHEAPLY MADE FOR SUCKERS

Very helpful. Couldnt work out how to reinsert the spring, but your video helped immensely.

Thank you. I don’t have this issue. But it may help along the line. Any chance you have a video on fixing the button? I think I pushed it in too hard it is stuck in the on position. Thank you.

I have a Bella toaster oven that has barely been used. The timer switch stopped working. I was going to discard it until i found this video. It took me about 20 minutes to fix it and now it is as good as new again. I can't imagine how many of these appliances get thrown out when a simple fix would give them a longer life.. Thank you TheIVJackal.

No way would I want to use that mangled product, let alone use it. Imagine how it would feel to hold the rough-edges in your hand and how much dirt will collect in the uneven edges. Mine only works now if I constantly push the button. I will purchase a less expensive facial brush device because the Clarisonic should last a very long time based on the price.

Keep your day job mate.

my farberware toaster oven model 103738 wont heat, it doesnt have side panels, how can I repair it?

I took apart the Neutragena face brush , the little circuit board is glued in above the motor , so the Clarisonic ;looks easier to do maintenance on . I cleaned the contacts of the on off switch and it started working again i used Q Tips and Alcohol same thing i use on Computer mother boards ,NOT WATER I Great video very help full beats throwing it away and paying 75$ or what ever they cost

Excellent video brother. Direct and clearly explained, entire repair took less than 30 minutes. Thank you.

thanks for keeping it free of music

Everybody should really take my advice and get a rotary drill kit (Dremel) with a thin saw blade and gently cut slowly around the gap between both sides. In less then 2 minutes your done and ready to replace the batteries and seal it together with silicone and let it set for 24 hours. Done!

The best way to open the produce is to cut all around the housing right between where the joint each other with a rotary cutting blade and a steady hand in less than one minute.

big chungus

But how to make it waterproof again? 😳

Thank you for the video. I would have destroyed my gfs clarisonic. I really appreciate your insight

Two words. Duct tape.

When I soldered the final connection the green LED started blinking. When I press the power button it just blinks green 15 times consecutively. I used eneloop batteries and they come charged. To sum it up, is there some sort of reset I need to do, or must I put it on the charger for 24 hours even with charged batteries? You would think it would just work off the bat. I also have not put the back on yet, but don’t see why that would matter. Any help would be much appreciated!

Where do you get these batteries? I can't get anyone to find these type batteries.....I called a battery shop today and they acted likethese batteries were hard to get! These are only standard rechargable batteries from what I can see.

Thanks! My Oster 6081 toaster oven's timer was acting strange (stayed on all the time and the bell sounded funny). I opened it and couldn't find anything and the timer stopped working and it fell apart (that little arm thingy). So I ordered a new timer online (DKJ/1-60 timer if someone is interested) and it worked great except it didn't have a "stay on" setting like before. I looked online and it doesnt seem like they are available anymore. Anyway, I saw your video, dug out the old timer from the recycling and garbage put it back together like in your video and now it works! Thanks!

It's sealed with ultrasonic welding. The seal is created with pressure and vibration that "melts" the two housing parts together. I know, not helpful with charging, but just an FYI.

Awesome video man... Mine is Emerson and similar switch except mine turn on by trimmer switch the one you have in the middle. But it does has the bell in the back of it and it turns it on not the bake/Toast/Broil setting switch. And when I push it too far out to max time and hold it or push the knob down then it turn on. I am pretty sure that is the problem

In my opinion, Clarisonic do NOT seal this unit to make it waterproof,!!! They seal it so you CAN’T replace the batteries easily!! This sealing trick leaves folks with no choice but to buy another new one if they really love the device.....another sale - and money in Clarisonic’s bank account. If these units were repairable, Clarisonic would only make money from NEW customers - not also from customers who are FORCED into the situation of having to purchase a new whole package, at some considerable cost!!! I’d rather have a Clarisonic that was NOT rotally waterproof, fastened with fairly easy open screws, with a suction grip outer edge seam all around it - and with a simple clip in cradle where you could insert new batteries!! Let’s face it....have you REALLY got to use this while taking a shower? It just took too long using the Clarisonic body brush option, and I found it not very effective in body skin exfoliation. There are other great, simple and fast exfoliating methods for the shower. I used to (batteries now dead) use mine at my bathroom sink, looking through a mirror. Only the brush head got slightly wet, so there was absolutely no need for the “totally waterproof” feature that Clarisonic throw out. Wouldn’t YOU rather have an EASILY REPAIRABLE one - instead of a fully waterproof one??? I know I would. Rant over......

I used an X-Acto knife heated on the gas stove ,it cuts the plastic nicely ,it's working now

Your a legend thank you

Excellent Idea. Thanks

Excelent video, dear gentleman!!! There's nothing similar in UA-cam. Your tutorial saved my oven!!! YOU GOT MY LIKE!!!!!!!!!!!!

Hey do you think is easy to unplug one the heating elements so it doesn't work? I noticed that my oven bake setting uses both heating elements and I want only the bottom one. Because toast setting already has the both on anyway.

Thanks so much ,my wife brings me your video and her Clarisonic face scrubber and says here you go ... I watched your video replaced the bad batteries did a little bit of taping and soldering it's back in business. I really appreciate the information about opening it up I would have destroyed it. Thanks again and keep up the good work..

Great video man! Well detailed, helped my girl who had the same problem. Thank you!

he freaking destroyed it. really?

sumer

well, sadly I'm not sure mine's going to work. the ticking part of it seems to have a mind of it's own. sometimes ticking and sometimes not. The problem I had before was that even when the timer was done, the oven would turn off but it would keep ticking, and because it was ticking, the knob was still turning and eventually it would turn to the "stay on" position causing the oven to turn back on! I checked the metal plate and turning it manually, it looks like it is making contact, and when it's not suppose to, it's not making contact. So doing what it's suppose to be doing. So, that has me confused.

Thanks a bunch!! My Farberware oven timer would not stop so then it would never shut off and I would have to unplug it. SO annoying! So, I think, as you mentioned, the opposite occurs when the metal plate is too high, and I am right now about to lower it and hopefully it will do the trick!

can you test the knobs for continuity. because mine doesnt heat the light is on but it does not get hot

I'm worried about whether super glue or JB weld will stand up to the heat. Good video. Our toaster oven contacts seem to stay on even after the timer counts down to zero.

How has it held up so far?

In my case the knob turns fine, but, as I let it go it quickly turns back to its original position by itself. I am guessing some spring (gear) got loose inside. How did you remove the knob? Did you pry it off?

I took it apart by sawing a groove with a hacksaw blade at the top and the bottom of the unit. Then I used a wood chisel inserted into the groove to break and pry the the shells apart. This one had much more silicone that the one here. The entire shell is sealed. It took 1 minute. It is very likely you will break it. This thing is just a vibrator brush. I can't believe my wife paid over $125.00 for this thing! It's only worth $5.00. I see some of these for $250.00 Talk about a ripoff! Women and their vanity! I am her husband.

wandering if cooking in oven makes glue gooey enough to pull apart.